Asus V2-PH2 Manuel d'utilisateur télécharger pdf (Page 39)

2-21

ASUS Vintage V2-PH2

2.10 Re-connecting cables

You may have disconnected some cables when you were installing

components. You must re-connect these cables before you replace the

chassis cover.

LED cables

Connect the reset button, power switch, power LED, and HDD LED

cables to their respective leads in the system panel connector on the

motherboard. See page 4-12 for the system panel descriptions.

HDD LED

Power LED

Power Switch

Reset button

System Panel Connector

* Requires an ATX power supply.

PANEL

PLED-

PWR

+5V

Speaker

Ground

RESET

Ground

Reset

Ground

PWRSW

PLED+

IDE_LED-

IDE_LED+

IDE_LED

PLED SPEAKER

1 2 ... 34 35 36 37 38 39 40 41 42 43 44 ... 101 102

Vintage V2-PH2 1
Second Edition V2 2
March 2006 2
Table of contents 3
Safety information 7
About this guide 8
System package contents 10
System introduction 11
1.2 Front panel 12
1.1 Welcome! 12
ASUS Vintage V2-PH2 13
1.3 Rear panel 14
Voltage selector 16
1.4 Internal components 17
Basic installation 19
2.1 Preparation 20
2.2 Before you proceed 20
panel assembly 21
2.4.1 Overview 22
2.4.2 Installing CPU 22
2.5 Installing a DIMM 26
Qualified Vendors Lists (QVL) 27
DDR2-533 27
DDR2-667 28
2.5.3 Removing a DDR2 DIMM 29
2.5.2 Installing a DDR2 DIMM 29
2.6 Expansion slots 30
2.6.4 PCI slots 32
2.6.3 PCI Express x1 slot 32
2.6.5 PCI Express x16 slot 32
Serial ATA cable 36
Serial ATA power 36
IDE ribbon cable 37
Power cable 37
Floppy ribbon 38
2.10 Re-connecting cables 39
and side cover 40
Starting up 41
3.3 Support CD information 42
3.2 Powering up 42
3.3.1 Running the support CD 43
3.3.2 Utilities menu 44
3.3.4 Manuals menu 45
3.3.3 Make Disk 45
3.4 Software information 46
Installing PC Probe II 47
Launching PC Probe II 47
Using PC Probe II 47
Preferences 48
Hardware monitor panels 49
WMI browser 50
DMI browser 50
PCI browser 51
Configuring PC Probe II 52
Motherboard info 53
Chapter 4: Motherboard info 54
4.3 Jumpers 55
Keyboard Power Setting 57
4.4 Connectors 58
NOTE: Orient the red markings 59
(usually zigzag) on the IDE 59
CPU FAN IN 60
CPU FAN PWM 60
Right Audio Channel 61
Left Audio Channel 61
(Default) 63
+5VSB_MB 63
Chassis Signal 63
Requires an ATX power supply 64
BIOS setup 65
DOS environment 66
XP environment 66
2000 environment 66
5.1.2 ASUS EZ Flash utility 67
5.1.3 AFUDOS utility 68
Updating the BIOS file 69
5.1.5 ASUS Update utility 72
5.2 BIOS setup program 75
5.2.2 Menu bar 76
5.2.1 BIOS menu screen 76
5.2.3 Navigation keys 76
5.3 Main menu 78
Master/Slave 79
5.3.5 System Information 80
5.4 Advanced menu 81
Legacy USB Support [Auto] 82
BIOS EHCI Hand-off [Enabled] 82
Overclocking [Auto] 83
CPU Frequency [XXX] 83
Memory Clock Mode [Auto] 84
OverClock Memory Clock [XXX] 84
5.4.3 CPU Configuration 85
Enhanced C1 Control [Auto] 86
NorthBridge Configuration 87
5.4.4 Chipset 87
Advanced NB 88
SouthBridge Configuration 89
Parallel Port Address [378] 90
Parallel Port Mode [EPP+ECP] 90
Parallel Port IRQ [IRQ7] 90
5.4.6 PCI PnP 91
5.5 Power menu 92
5.5.5 APM Configuration 93
5.5.6 Hardware Monitor 94
CPU Voltage Selection 95
Q-Fan Control [Disabled] 95
5.6 Boot menu 96
5.6.3 Security 98
Change User Password 99
5.7 Exit menu 100
Exit & Discard Changes 101
Discard Changes 101
Load Setup Defaults 101
Chapter 5: BIOS setup 102

Commentaires sur ces manuels

Pas de commentaire

Asus V2-PH2 Manuel d'utilisateur Page 39

Commentaires sur ces manuels

Produits connexes et manuels pour Ordinateurs Asus V2-PH2