Asus RS100-E4/PI2 Manuel d'utilisateur Page 38
- Page / 156
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 3: Installation options3-4
2. Attach the inner rail to the correspoding side of the chassis and secure
with three inner rail screws. Make sure the rail is oriented as shown.
3. Attach the second inner rail to the other side of the chassis and secure
with three inner rail screws.
4. Select one unit of space (1U) on
the rack where you wish to install
the server.
5. Place three (3) nuts on the front
and three at the back. Do the
same to the corresponding side
of the rack.
Nuts
6. Adjust the length of the outer
rail to t the length of the rack
cabinet then fasten the two
screws.
- RS100-E4/PI2 1
- First Edition V1 2
- October 2006 2
- Contents 3
- Safety information 8
- About this guide 9
- References 10
- Conventions 10
- Typography 10
- Product introduction 11
- 1.1 System package contents 12
- 1.2 System specications 13
- 1.3 Front panel features 14
- 1.4 Rear panel features 14
- 1.5 Internal features 15
- 1.6 LED information 16
- Hardware setup 17
- 2.1 Chassis cover 18
- 2.1.2 Installing the cover 19
- Chapter 2: Hardware setup2-4 20
- 2.2 Motherboard information 21
- 2.3.1 Installing the CPU 22
- Heatsink plastic cover 25
- 2.4 System memory 26
- 2.4.3 Installing a DIMM 27
- 2.4.4 Removing a DIMM 27
- 2.5 Replaceable components 28
- System blower screws 29
- SATA L-type 30
- ATX power connector 30
- SATA signal cable 30
- P5M2-M/RS100-E4 31
- SATA drive plate 32
- To install ODD: 33
- Installation options 35
- 3.1 Rackmount rail kit items 36
- 3.2 Attaching the rack ears 36
- 3-3ASUS RS100-E4/PI2 37
- 3-5ASUS RS100-E4/PI2 39
- Rack screw 40
- Motherboard Info 41
- 4.1 Motherboard overview 42
- Layout contents 43
- (Default) 45
- Clear RTC 45
- ASUS RS100-E4/PI2 4-7 47
- P5M2-M/RS100-E4 VGA Setting 47
- INTEL RAID ROM 48
- LSI RAID ROM 48
- Normal BIOS recovery 49
- 4.3 Connectors 50
- 4.3.2 Internal connectors 51
- NOTE: Orient the red markings 52
- (usually zigzag) on the IDE 52
- Conn ector Sett ing Use 53
- ADD_IN_CARD_ACT# 54
- I2C_DATA 56
- 24-pin Power Connector 57
- AUX_PANEL1 58
- ASUS RS100-E4/PI2 4-1 9 59
- 5-2 Chap ter 5: BIOS setup 62
- 5.1.2 AFUDOS utility 63
- Updating the BIOS file 64
- ASUS RS100-E4/PI2 5-5 65
- 5.1.4 ASUS Update utility 68
- ASUS RS100-E4/PI2 5-9 69
- 5.2 BIOS setup program 71
- 5.2.2 Menu bar 72
- 5.2.3 Navigation keys 72
- 5.2.1 BIOS menu screen 72
- ASUS RS100-E4/PI2 5-1 3 73
- 5.3 Main menu 74
- Type [Auto] 75
- LBA/Large Mode [Auto] 75
- 5.3.5 IDE Configuration 76
- ALPE and ASP [Disabled] 77
- 5.3.6 System Information 78
- 5.4 Advanced menu 79
- 5.4.2 MPS Configuration 80
- Remote Access [Disabled] 81
- Serial port number [COM1] 81
- Flow Control [None] 81
- 5.4.4 Trusted Computing 82
- 5.4.5 CPU Configuration 83
- 5.4.6 Chipset Configuration 84
- Spread Spectrum [Disabled] 85
- PEG Port Configuration 85
- PEG Port [Enabled] 85
- Serial Port2 Mode [Normal] 86
- Parallel Port IRQ [IRQ7] 86
- 5.4.8 PCI PnP 87
- 5.5 Power Conguration 88
- RTC Alarm Date (Days) [15] 89
- System Time [12:30:30] 89
- 5.5.2 Hardware Monitor 90
- 5.6 Boot menu 91
- 5.6.1 Boot Device Priority 92
- 5.6.2 Hard Disk Drives 92
- ASUS RS100-E4/PI2 5-3 3 93
- 5.6.4 Security 94
- Change User Password 95
- Clear User Password 96
- Password Check [Setup] 96
- 5.7 Exit menu 97
- Load Setup Defaults 98
- RAID Conguration 99
- 6.1 RAID congurations 100
- ASUS RS100-E4/PI2 6-3 101
- BIOS Setup 101
- 6.2 Intel 102
- ROM Utility 102
- ASUS RS100-E4/PI2 6-5 103
- ASUS RS100-E4/PI2 6-7 105
- 6.2.3 Deleting a RAID set 106
- 6.2.5 Exiting the Intel 107
- Matrix Storage Manager 107
- utility 107
- 6.2.6 Rebuilding the RAID 108
- Utility 109
- 6.3.1 Creating a RAID set 111
- Using Easy Configuration 112
- ASUS RS100-E4/PI2 6-1 5 113
- ASUS RS100-E4/PI2 6-1 7 115
- Using New Configuration 116
- ASUS RS100-E4/PI2 6-1 9 117
- ASUS RS100-E4/PI2 6-2 1 119
- Using the Initialize command 120
- ASUS RS100-E4/PI2 6-2 3 121
- Using the Objects command 122
- ASUS RS100-E4/PI2 6-2 5 123
- Using the Rebuild command 125
- Using the Check Consistency 127
- ASUS RS100-E4/PI2 6-3 3 131
- 6.4 Global Array Manager 132
- Driver installation 133
- 7.1 RAID driver installation 134
- 2000/2003 Server OS 135
- LSI Logic SATA RAID 136
- Intel Matrix Storage 137
- ASUS RS100-E4/PI2 7-7 139
- Enterprise ver. 3.0 140
- ASUS RS100-E4/PI2 7-9 141
- SuSE Linux 143
- 7.2 LAN driver installation 145
- insmodbcm5700.o 146
- makeinstall 146
- 7.3 VGA driver installation 147
- 7.3.2 Windows 148
- 2003 Server 148
- 7.3.3 Red Hat 148
- utilities installation 149
- 7.4.4 Utilities menu 150
- 7.4.5 Contact information 151
- Reference 153
- A.1 Intel 154
- A.2 Enhanced Intel SpeedStep 154
- Technology (EIST) 154
- A.2.2 Using the EIST 155
- A-4 Appendix: CPU features 156
Produits connexes et manuels pour Matériel informatique Asus RS100-E4/PI2
(142 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels