Asus RS100-E4/PI2 Manuel d'utilisateur Page 32
- Page / 156
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 2: Hardware setup2-16
2. Locate the Serial ATA drive plate
under the optical disk drive (ODD)
bay.
SATA drive plate
3. Connect the Serial ATA signal cable
and ATX power connectors. Use
the L-type Serial ATA connector to
connect to the hard drive.
SATA L-type
connector
ATX power connector
SATA signal cable
4. Insert the Serial ATA drive into the
drive plate as shown.
To install secondary Serial ATA drive:
1. If you have an ODD installed,
remove the ODD bay rst before
you install a secondary SATA disk
drive.
To remove, disconnect the ODD
cable and power cable then use
a screwdriver to remove all four
screws.
- RS100-E4/PI2 1
- First Edition V1 2
- October 2006 2
- Contents 3
- Safety information 8
- About this guide 9
- References 10
- Conventions 10
- Typography 10
- Product introduction 11
- 1.1 System package contents 12
- 1.2 System specications 13
- 1.3 Front panel features 14
- 1.4 Rear panel features 14
- 1.5 Internal features 15
- 1.6 LED information 16
- Hardware setup 17
- 2.1 Chassis cover 18
- 2.1.2 Installing the cover 19
- Chapter 2: Hardware setup2-4 20
- 2.2 Motherboard information 21
- 2.3.1 Installing the CPU 22
- Heatsink plastic cover 25
- 2.4 System memory 26
- 2.4.3 Installing a DIMM 27
- 2.4.4 Removing a DIMM 27
- 2.5 Replaceable components 28
- System blower screws 29
- SATA L-type 30
- ATX power connector 30
- SATA signal cable 30
- P5M2-M/RS100-E4 31
- SATA drive plate 32
- To install ODD: 33
- Installation options 35
- 3.1 Rackmount rail kit items 36
- 3.2 Attaching the rack ears 36
- 3-3ASUS RS100-E4/PI2 37
- 3-5ASUS RS100-E4/PI2 39
- Rack screw 40
- Motherboard Info 41
- 4.1 Motherboard overview 42
- Layout contents 43
- (Default) 45
- Clear RTC 45
- ASUS RS100-E4/PI2 4-7 47
- P5M2-M/RS100-E4 VGA Setting 47
- INTEL RAID ROM 48
- LSI RAID ROM 48
- Normal BIOS recovery 49
- 4.3 Connectors 50
- 4.3.2 Internal connectors 51
- NOTE: Orient the red markings 52
- (usually zigzag) on the IDE 52
- Conn ector Sett ing Use 53
- ADD_IN_CARD_ACT# 54
- I2C_DATA 56
- 24-pin Power Connector 57
- AUX_PANEL1 58
- ASUS RS100-E4/PI2 4-1 9 59
- 5-2 Chap ter 5: BIOS setup 62
- 5.1.2 AFUDOS utility 63
- Updating the BIOS file 64
- ASUS RS100-E4/PI2 5-5 65
- 5.1.4 ASUS Update utility 68
- ASUS RS100-E4/PI2 5-9 69
- 5.2 BIOS setup program 71
- 5.2.2 Menu bar 72
- 5.2.3 Navigation keys 72
- 5.2.1 BIOS menu screen 72
- ASUS RS100-E4/PI2 5-1 3 73
- 5.3 Main menu 74
- Type [Auto] 75
- LBA/Large Mode [Auto] 75
- 5.3.5 IDE Configuration 76
- ALPE and ASP [Disabled] 77
- 5.3.6 System Information 78
- 5.4 Advanced menu 79
- 5.4.2 MPS Configuration 80
- Remote Access [Disabled] 81
- Serial port number [COM1] 81
- Flow Control [None] 81
- 5.4.4 Trusted Computing 82
- 5.4.5 CPU Configuration 83
- 5.4.6 Chipset Configuration 84
- Spread Spectrum [Disabled] 85
- PEG Port Configuration 85
- PEG Port [Enabled] 85
- Serial Port2 Mode [Normal] 86
- Parallel Port IRQ [IRQ7] 86
- 5.4.8 PCI PnP 87
- 5.5 Power Conguration 88
- RTC Alarm Date (Days) [15] 89
- System Time [12:30:30] 89
- 5.5.2 Hardware Monitor 90
- 5.6 Boot menu 91
- 5.6.1 Boot Device Priority 92
- 5.6.2 Hard Disk Drives 92
- ASUS RS100-E4/PI2 5-3 3 93
- 5.6.4 Security 94
- Change User Password 95
- Clear User Password 96
- Password Check [Setup] 96
- 5.7 Exit menu 97
- Load Setup Defaults 98
- RAID Conguration 99
- 6.1 RAID congurations 100
- ASUS RS100-E4/PI2 6-3 101
- BIOS Setup 101
- 6.2 Intel 102
- ROM Utility 102
- ASUS RS100-E4/PI2 6-5 103
- ASUS RS100-E4/PI2 6-7 105
- 6.2.3 Deleting a RAID set 106
- 6.2.5 Exiting the Intel 107
- Matrix Storage Manager 107
- utility 107
- 6.2.6 Rebuilding the RAID 108
- Utility 109
- 6.3.1 Creating a RAID set 111
- Using Easy Configuration 112
- ASUS RS100-E4/PI2 6-1 5 113
- ASUS RS100-E4/PI2 6-1 7 115
- Using New Configuration 116
- ASUS RS100-E4/PI2 6-1 9 117
- ASUS RS100-E4/PI2 6-2 1 119
- Using the Initialize command 120
- ASUS RS100-E4/PI2 6-2 3 121
- Using the Objects command 122
- ASUS RS100-E4/PI2 6-2 5 123
- Using the Rebuild command 125
- Using the Check Consistency 127
- ASUS RS100-E4/PI2 6-3 3 131
- 6.4 Global Array Manager 132
- Driver installation 133
- 7.1 RAID driver installation 134
- 2000/2003 Server OS 135
- LSI Logic SATA RAID 136
- Intel Matrix Storage 137
- ASUS RS100-E4/PI2 7-7 139
- Enterprise ver. 3.0 140
- ASUS RS100-E4/PI2 7-9 141
- SuSE Linux 143
- 7.2 LAN driver installation 145
- insmodbcm5700.o 146
- makeinstall 146
- 7.3 VGA driver installation 147
- 7.3.2 Windows 148
- 2003 Server 148
- 7.3.3 Red Hat 148
- utilities installation 149
- 7.4.4 Utilities menu 150
- 7.4.5 Contact information 151
- Reference 153
- A.1 Intel 154
- A.2 Enhanced Intel SpeedStep 154
- Technology (EIST) 154
- A.2.2 Using the EIST 155
- A-4 Appendix: CPU features 156
Produits connexes et manuels pour Matériel informatique Asus RS100-E4/PI2
(142 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels