Asus RS100-E8-PI2 Manuel d'utilisateur Page 70
- Page / 158
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 4: Motherboard information
4-18
13. Auxiliary panel connector (20-2 pin AUX_PANEL1)
This connector is for additional front panel features including front panel SMB, Locator
LED and switch, chassis intrusion, and LAN LEDs.
1. Front panel SMB (6-1 pin FPSMB)
These leads connect to the front panel SMBus cable.
2. LAN activity LED (2-pin LAN1LINK and 2-pin LAN2LINK)
These leads are for Gigabit LAN activity LEDs on the front panel.
3. Chassis intrusion (4-1 pin AUX_CHASSIS)
These leads are for the intrusion detection feature for chassis with an intrusion
sensor or microswitch. When you remove any chassis component, the sensor
triggers and sends a high-level signal to these leads to record a chassis intrusion
event. The default setting is short CASEOPEN and GND pin by jumper cap to
disable the function.
4. Locator LED (2-pin AUX_LOCLED1 and 2-pin AUX_LOCLED2)
These leads are for the Locator LED1 and LED2 on the front panel. Connect the
Locator LED cables to these 2-pin connectors. The LEDs will light up when the
Locator button is pressed.
5. Locator Button/Switch (2-pin AUX_BMCLOCBNT)
These leads are for the locator button on the front panel. This button queries the
state of the system locator.
- RS100-E8-PI2 1
- User Guide 1
- Revised Edition V2 2
- September 2013 2
- Contents 3
- Australia statement notice 7
- Safety information 8
- About this guide 9
- References 10
- Conventions 10
- Typography 10
- Product overview 11
- 1.1 System package contents 12
- 1.2 Serial number label 12
- 1.3 Systemspecications 13
- 1.4 Front panel features 15
- 1.5 Rear panel features 15
- 1.7 LED information 17
- 1.7.2 LAN (RJ-45) LEDs 18
- Hardware setup 19
- 2.1 Chassis cover 20
- ASUS RS100-E8-PI2 21
- Chapter 2: Hardware setup 22
- 2.2.1 Installing the CPU 23
- Retention 25
- Load lever 25
- Retention tab 25
- 2.3 System memory 28
- Locked Retaining Clip 29
- Unlocked retaining clip 29
- DIMM notch 29
- DIMM slot key 29
- 2.4 Hard disk drives 31
- 2.5-inch SSD 33
- SSD drive tray 33
- HDD drive tray 33
- HDD bay 1 33
- ODD cable 36
- HDD bay 2 36
- 2.5 Expansion card 39
- 2.7.1 Chassis fans 43
- Optical disk drive slot 44
- LAN port 3 45
- LAN port 1~2 45
- Rackmount installation 47
- 3.1 Rackmount rail kit items 48
- Rack screw 51
- Motherboard Info 53
- 4.1 Motherboard layout 54
- Layout contents 55
- 4.2 Onboard LEDs 57
- 4.3 Jumpers 59
- 4.4 Connectors 62
- 4.4.2 Internal connectors 63
- BIOS setup 71
- 5.1.3 BUPDATER utility 74
- 5.2 BIOS setup program 76
- 4.2.2 Menu bar 77
- 5.2.1 BIOS menu screen 77
- PCI Subsystem Settings 78
- ACPI Settings 78
- Trusted Computing 78
- 5.3 Main menu 79
- 5.4 Advanced menu 80
- 5.4.1 CPUConguration 81
- CPU C states [Enabled] 83
- CFG lock [Enabled] 84
- Package C State limit [AUTO] 84
- LakeTiny Feature [Disabled] 84
- ACPI T State [Enabled] 84
- 5.4.2 PCH-IOConguration 85
- 5.4.3 SATAConguration 86
- VT-d [Enabled] 87
- Enable NB CRID [Disabled] 87
- VGA Priority [Offboard] 87
- MemoryConguration 88
- Memory Scrambler [Enabled] 88
- Memory Remap [Enabled] 88
- GDXC Support [Disabled] 88
- 5.4.5 PCI Subsystem Settings 89
- 5.4.6USBConguration 90
- 5.4.7 TPM 92
- 5.4.8 ACPI Settings 92
- 5.4.9 WHEA Support 93
- 5.4.11 Intel 94
- Server Platform Services 94
- 5.4.15 APM 97
- 5.4.16 Network Stack 98
- 5.5 Event Logs menu 99
- 5.6 Boot menu 100
- Boot Option Priorities 101
- Drive BBS Priorities 101
- CSM Parameters 102
- 5.7 Monitor menu 103
- 5.8 Security 104
- User Password 105
- Secure Boot Menu 105
- Secure Boot Control [Enabled] 105
- Secure Boot Mode [Standard] 105
- Key Management 106
- Image Execution Policy 106
- 5.10 Exit menu 107
- 5.9 Tool menu 107
- Discard Changes & Reset 108
- Restore Defaults 108
- RAIDconguration 109
- (Data striping) 110
- (Data mirroring) 110
- 6.1.3 Setting Jumpers 111
- 6.2 Intel 112
- ROM Utility 112
- 6.2.1 Creating a RAID set 113
- 6.2.2 Deleting a RAID set 115
- 6.2.5 Rebuilding the RAID 117
- 6.2.4 Exiting the Intel 117
- SATA Option ROM utility 117
- 6.3 Intel 120
- 6.3.1 Creating a RAID set 121
- Chapter 6: RAID conguration 122
- 6.3.2 Changing a Volume Type 123
- 6.3.3 Deleting a volume 124
- 6.3.4 Preferences 125
- Driver installation 127
- 7.1 RAID driver installation 128
- During Windows 130
- Server 2008 OS installation 130
- 7.3 Running the Support DVD 132
- 7.3.2 Utilities menu tab 133
- 7.3.1 Drivers menu tab 133
- 7.3.3 MakeDisk menu tab 134
- 7.3.4 Manual menu 134
- 7.3.6 Installing the Intel 135
- 7.6 Installing the Intel 148
- C22x MEI NULL HECI driver 148
- 7.7 Installing the Intel 150
- I210 Gigabit Adapter driver 150
- Technical Support 155
- Appendix 158
Produits connexes et manuels pour Matériel informatique Asus RS100-E8-PI2
(196 pages)
(2 pages)
(114 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels